Samsung Ice Maker Not Making Ice? 7 Causes and What to Check

Freezer & Ice Maker Repair · Concord Appliance Care

Samsung Ice Maker Not Making Ice? 7 Causes and What to Check

You open the freezer, lift the ice bucket, and it is empty — again. Or the bucket has a few cubes fused into one solid lump, and nothing has dropped in days. Samsung ice makers fail in their own specific ways, and the fixes that work on other brands do not always apply here. Samsung even has its own warning about this: do not try to defrost the ice maker yourself. That warning is the first thing to know, because half the advice on the internet tells you to do exactly that.

Quick answer: On a Samsung, check five things first, in Samsung’s own order: the Ice Off icon, the freezer temperature, the ice bucket, the Test button, and the water supply. The freezer must be at 0°F or colder for the ice maker to run at all. If Ice Off is lit, the ice maker is switched off. If the bucket is not seated properly, the ice maker thinks it is full. The Test button — press and hold until it chimes — runs one full harvest and fill cycle and tells you whether the ice maker itself works. And the water test is simple: the dispenser should fill 6 ounces in under 10 seconds. If the ice maker is frozen over with a sheet of ice, or the bucket is stuck solid, stop — Samsung says that needs service, not a hair dryer. The seven causes below follow the same order, with the Samsung-specific detail for each one.

Which Samsung Ice Maker Do You Have?

Samsung does not use one ice maker design. The checks below differ by design, so find yours first. The model number is on a label inside the fridge — usually on the left wall of the fresh-food section or inside the freezer. Write it down; it is the first thing a technician will ask for, and it is how you check warranty coverage.

DesignWhere the ice maker isWhat differs
French-door, in-door ice makerIn an insulated ice room in the left fridge doorMost common Samsung design — and the one that freezes over. Cold air is ducted in from the freezer. Makes about one tray every 45–65 minutes.
Freezer-compartment ice makerInside the freezer — side-by-side, bottom-freezer, top-freezerSimpler and slower: about one tray every 85 minutes. The Test button works the same way but the test takes about 30 seconds instead of 6 minutes.
Dual ice makers (Bespoke)Two makers in the bottom freezer — cubed on the left, Ice Bites on the rightEach maker has its own Test button and its own Ice Off icon, but only one button on the panel — tap it repeatedly until neither icon is lit. The Ice Bites bucket must go in the right direction, or the scoop holder blocks the maker.
Family Hub / SmartThings modelsSame hardware, app controlsIce Off is controlled in the Fridge Manager app or SmartThings. Samsung says a firmware update can help prevent freeze-over on these models — keep the fridge connected.

Two model-specific notes from Samsung: on RS27T and RS22T models there are two water lines, and if they are cross-connected, water and ice dispensing will not work correctly. And on top-freezer models the control is an “Ice On” icon — leave it lit — which is the opposite of the Ice Off icon on other models.

The 5-Minute Samsung Check — Do These First

These are Samsung’s own steps, in Samsung’s own order. Do them before anything else — most no-ice calls end somewhere in this list.

1. Is Ice Off lit?

Most Samsung models have an Ice Off icon on the display. Lit means the ice maker is off. It must NOT be lit for ice production. On Family Hub models, check it in the Fridge Manager app; on SmartThings models, in the app. If the Ice Off icon is blinking, that is not an error code — it means the ice bucket is not inserted correctly, or not inserted at all. Reseat the bucket and the blinking should stop.

2. Is the freezer at 0°F or colder?

The freezer needs to be at 0°F or less for the ice maker to produce ice — even on models where the ice maker sits in the fridge compartment, because the cold air comes from the freezer. Check the displayed temperature with a thermometer if you have one; the display setting is not always the real temperature. If it is above 0°F, set it to 0°F or lower and turn on Power Freeze, then wait 3 hours and check again. If the freezer cannot get cold enough at all, the problem is cooling, not the ice maker — start with our guide on refrigerator not cooling instead.

3. Is the ice bucket seated — and is it clear?

On in-door models the ice bucket must be fully seated and locked in position. On freezer models the freezer door must be closing correctly. Take the bucket out and put it back in firmly until it locks. And check what is inside it: the only thing that should be in the ice bucket is ice. A scoop, a bag, or food stored in the bucket can make the ice maker detect a full bucket and stop ejecting. If there is frost in the freezer or on the ice bucket, that is a separate problem to fix first.

4. Press the Test button — once

There is a Test button on Samsung ice makers. On most models you need to remove the ice bucket to see it. On Bespoke dual makers, reach your hand underneath the ice maker — under the vent, above the bucket — and feel for it. Press and hold the Test button until you hear a chime, which may take up to 10 seconds. If it does not chime, unplug the fridge — or switch it off at the breaker — for 2 minutes, then try again. The test takes about 6 minutes on an ice maker in the fridge compartment, or about 30 seconds for one in the freezer. Watch it move, and at the end the water valve should hum and pour water into the ice maker. One chime means the ice maker passed the test. Multiple chimes, or no response at all after the power cycle, means it needs service. Do not press Test repeatedly — especially not when the tray holds ice or water, or the water may overflow and the ice may jam. And if an error code appears after the power cycle, write it down and do not keep resetting; note the code and call for service.

5. Check the water — 6 ounces in under 10 seconds

Samsung’s minimum water pressure is 20 psi. Test it at the dispenser: hold a measuring cup under it and see if you get 6 ounces — three-quarters of a cup — in under 10 seconds. If the flow is slow, take the water filter out and test again. If the flow is normal without the filter, the filter is the problem — replace it, and use only a Samsung filter for your model. Samsung rates its filters for 300 gallons, about 6 months in an average household, and says a filter past its life can reduce pressure enough to stop ice production. If the flow is still slow with the filter out, the supply pressure is too low or the supply valve is not fully open. Check that the valve behind the fridge is open all the way, and that the water line is not pinched or kinked. If you use a reverse-osmosis system, it may be dropping the pressure too low — that is a plumber’s job, not a fridge repair. If the ice maker never worked properly since the water line was adjusted, confirm the pressure is at least 20 psi before going further.

After a fix, give it time: Samsung says you should begin to see normal ice production within 3 hours, and it may take a full 24 hours for production to return to normal amounts — about 2 trays of ice every 3 hours. Dispense ice occasionally during that period. If ice piles up at one end of the bucket, the ice maker thinks it is full and stops.

Symptom Decoder: What Your Samsung Ice Maker Is Telling You

SymptomMost Likely CauseSafe Check
No ice at allIce Off on, freezer too warm, no water reaching the makerThe 5-minute check above, in order
Ice in the bucket, but it will not dropBucket not seated, clumped ice jamming the auger, harvest failureReseat the bucket; dump clumped ice; run the Test button once
Ice maker frozen over, bucket stuckWarm air leaking into the ice room past a sealNone — do not force it, do not use a hair dryer. Call for service.
Water dispenser works, ice maker does notFault is in the ice-maker water path only — frozen fill tube, ice-side valve, ice-pipe heaterIce Off, temperature, Test button, then the flow test
Water pooling under the fridgeDefrost drain, fill-tube leak, valve seeping, filter not seated, loose fittingFind where the water starts — and keep water away from outlets and cords
Cloudy, small, or bad-tasting cubesCloudy is normal. Small means low water flow. Dark flecks mean a bad filter or dirt in the supply.Flow test, then the filter test
Ice coming, just very slowlyWarm freezer, doors opened often, low pressure, old filter, ice piling at one endTemperature, Power Freeze, flow test, shift the ice forward

The 7 Causes, in Check Order

1. Ice maker not making ice at all

What you notice: the bucket stays empty for days, even though the fridge is cold and the dispenser works. The possible causes, in Samsung’s order: Ice Off is on; the freezer is above 0°F; the bucket is not seated; the Test button fails; or the water is not reaching the maker — pressure below 20 psi, supply valve not fully open, expired filter, or a reverse-osmosis system dropping the pressure. The safe checks are the 5-minute check above. If the Test button chimes once and the valve fills at the end of the test, the ice maker itself works — the fault is in temperature or water. If it does not chime even after a 2-minute power cycle, or it chimes multiple times, the maker needs service. What a technician checks next: the water inlet valve (including the ice-side solenoid, which can fail while the dispenser side still works), the fill tube, and the ice maker module itself. The full generic diagnosis chain — valve, fill tube, module, mold heater — is covered on our freezer and ice maker repair in Concord, NC page.

2. Ice maker is not ejecting or dumping ice

What you notice: there is ice in the tray or bucket, but nothing drops — or the dispenser gives nothing when you press it, even though the bucket is not empty. First, separate two problems: ice that never leaves the tray is a harvest problem; ice in the bucket that never comes out of the door is a dispensing problem (auger, chute, or Child Lock). For harvest: reseat the bucket — a bucket that is not fully locked in will not eject. Dump the bucket if the cubes have fused into one lump; clumped ice jams the mechanism and can make the maker think the bucket is full. Shift ice forward in the bucket so it does not pile at one end. Then run the Test button once: if the tray rotates and the valve fills during the test, the motor and ejector work. If the tray stalls mid-cycle, clicks without ejecting, or never runs the test, the module or ejector motor is the likely fault. Do not pry cubes out of the tray and do not force the ejector arm — you will break the motor gears. What a technician checks: the ejector motor, the auger motor (a hum or click with no movement points at it), the thermistor that reads the mold temperature, and whether a frozen fill tube has spilled water that refroze the mechanism.

3. Ice maker appears frozen or stuck

What you notice: a sheet of ice over the ice maker, frost building up inside the ice room in the door, or a bucket you cannot pull out. This is the best-known Samsung French-door problem, and it is the one where the internet gives the worst advice. Samsung’s own words: “Do not attempt to defrost your ice maker, as this may damage the ice maker. Your ice maker has an automatic defrost function. If this is not working, then your ice maker needs service.” And for a stuck bucket: do not use force to remove it, and do not use a hair dryer to defrost it. Samsung’s technicians are told the same thing — never a heat gun or hair dryer in the ice room; they use a steamer. The cause, in plain terms: warm, humid kitchen air is leaking into the ice room past a seal that no longer seals — a bad ice bucket gasket, an ice route that does not close properly, or an air duct blocked with frost. Samsung has a technician service bulletin for exactly this problem on French-door models from 2014 onward (RF22K, RF23, RF24, RF25, RF26, RF28, RF30, RF31, RF32 and RF34 families), listing the same causes: inefficient defrost of the ice maker cooling loop, a blocked air duct, a failed auger motor fan, air infiltration past the bucket gasket, and water spraying or dripping. A one-time freeze-over after a power outage or a door left open is common and may not come back. A freeze-over that keeps coming back is a service call. What a technician checks: the ice-room seals and flapper, the air duct, the auger motor fan, and whether the ice room needs resealing. If your model is a Family Hub or SmartThings model, Samsung also says a firmware update can help prevent this — keep the fridge connected and check for updates before booking a repair.

4. Water dispenser works, but the ice maker does not

What you notice: water comes out of the dispenser normally, but the ice maker makes nothing. This symptom is useful, because it narrows the fault. Working water confirms the home supply, the main inlet and the filter are not completely blocked — so the fault is in the ice-maker water path only. The possible causes: the ice maker is switched off on its own Ice Off control; a frozen fill tube; the ice-side solenoid of the dual-port inlet valve, which can fail while the dispenser side still works; a failed ice-pipe heater (Samsung error code 33E); or a failed ice maker assembly. Also check the temperature — the dispenser can still work when the freezer is too warm for ice making, because the dispenser’s chilled reservoir is a different system. Safe checks: Ice Off, the 0°F temperature check, the Test button, and the flow test. If the Test button runs and the valve fills, the path is open and the problem is elsewhere. What a technician checks: the ice-side valve solenoid (tested for continuity), the fill tube and its heater, and the ice maker module. One caution: some guides suggest a forced-defrost button combination to thaw a frozen fill tube. Samsung gives homeowners no forced-defrost procedure — do not use one. A frozen fill tube is a symptom, not the root cause, and thawing it without fixing the cause just refreezes it.

5. Water pooling underneath the freezer or refrigerator

What you notice: water on the floor under or in front of the fridge, or water pooling under the crisper drawers inside. First, find where the water starts — dry everything, then watch for the first wet spot. That location names the cause. The most common cause is a clogged or frozen defrost drain: meltwater from the automatic defrost cycle backs up into the fridge section or onto the floor. Other causes: a cracked or overfilled drain pan; a leaking water supply line or a loose fitting at the wall valve or the rear inlet; a water inlet valve that does not fully close and keeps dripping; an ice-maker fill tube spraying or leaking inside the ice room; or a water filter that is not seated correctly or is cracked — on French-door models the filter sits under the crisper drawers, so a drip lands there. Clearing a defrost drain on most modern French-door and side-by-side models means removing the freezer’s rear interior panel, so treat that as a technician repair, not a homeowner step. Now the safety part: if water is pooling near an outlet, the power cord, or any electrical connection, do not touch the fridge — water and electricity together are a shock and fire risk. And learn to tell condensation from a leak. Some condensation on the outside of the fridge in very humid weather is normal — moisture in the air meeting a cold surface. A leak is water appearing where it should not be, repeatedly, in the same place. Our freezer and ice maker page covers the defrost-drain side of this in more detail — see freezer and ice maker repair in Concord, NC.

6. Ice cubes are cloudy, unusually small, or taste bad

What you notice: the cubes look white and foggy, or they come out small and shattered, or the ice tastes off. Start with the reassuring one: cloudy white ice is normal on a Samsung. Samsung says so directly — its ice makers use rapid freezing, which traps small amounts of minerals, oxygen and nitrogen inside the cube, giving it a cloudy appearance. A normal Samsung cube is cloudy white and shaped like an orange slice, and the minerals are not harmful — they are more common in areas with hard water. Small or shattered cubes are different: they mean low water flow. The ice maker does not get enough water before it freezes and dumps. Run the flow test — 6 ounces in under 10 seconds — check that the supply valve is fully open and the line is not pinched, then take the filter out and test again. If removing the filter fixes it, replace the filter. Dark flecks or dirty ice are not normal: the causes are an expired or damaged water filter, dirt in the water supply (for example after work on the home or neighborhood water lines), or a damaged ice bucket. Flush a few gallons through the dispenser, inspect the ice maker and bucket for visible damage, and replace the filter. If the ice is still dirty after a filter change, or you can see damage, it needs service. Clumped cubes mean the ice has sat in the bucket too long without being dispensed — Samsung says to dump the bucket about every other week so the maker can produce fresh ice. Slushy or frosty cubes usually mean frost in the ice bucket; fix the frost and the cubes should return to normal. For bad taste, the filter is the first thing to check — an expired filter is the named cause — along with the minerals in your water.

7. Ice production has become unusually slow

What you notice: ice is coming, just not fast enough to keep up — the bucket never fills, or it takes days to get a usable amount. First, know what normal looks like on a Samsung: a fridge-compartment ice maker makes about one tray every 45–65 minutes, a freezer-compartment maker about one tray every 85 minutes, and a tray is 8 cubes on a full-size refrigerator or 6 on a counter-depth model. Normal output is about 2 trays every 3 hours, and the maker can only hold 2 pounds of ice — a full bucket stops production. The causes of slow production, per Samsung: a freezer that is not cold enough (set 0°F or lower and use Power Freeze); doors opened often, which pauses production and lets warm air in; low water pressure; an expired filter; a fridge that is not level, which can stop water flowing properly through the ice maker; and ice piling at one end of the bucket, which makes the maker think it is full. The safe checks: temperature and Power Freeze, the flow test, the filter test, and shifting the ice forward in the bucket — or emptying some into bags in the freezer so the maker keeps running. If production is slow right after an install, a filter change, or a reset, give it the full 24 hours before judging it. If it is still slow after that, with the temperature and water both confirmed, the maker itself — or the cooling behind it — needs a diagnosis.

What the Error Code Means

If your Samsung shows a code, write it down — photograph the display — before you reset anything. The code is the machine telling you what it measured. Samsung’s own list is not complete, and codes vary by model, so if your code is not on this list, do not guess at it. Do not unplug the fridge or fiddle with the panel to make a code go away — Samsung says that makes it harder for a technician to diagnose and fix the issue. Every code below means the same thing for a homeowner: request service.

CodeWhat Samsung says it meansWhat to do
8EIce maker (freezer) sensor errorRequest service
14EIce maker sensor errorRequest service
33EIce pipe heater errorRequest service
39E / 39CIce maker function errorRequest service
40E / 40CIce room fan errorRequest service
Ice Off blinkingNot an error code — the ice bucket is not inserted correctly, or not inserted at allReseat the bucket
OF OF (or OFF OFF)Cooling Off mode — also called demo or shop mode. It disables cooling, ice making and the water dispenser.Not a fault. Turn Cooling Off mode off using your model’s instructions — service is not required.

Two cautions. First, other websites publish different meanings for these same codes — one repair guide, for example, calls 39E a communication fault and 40E a temperature sensor fault. Those contradict Samsung’s own list. Use Samsung’s meanings above. Second, some guides list codes 26E and 41E for Samsung ice makers. Neither appears on Samsung’s published error-code list, so this guide does not include them. If the same code comes back after a reset, it is indicating a real condition, not a glitch — note the code and call for service rather than resetting it again.

When to Call for Ice Maker Repair

Call once Ice Off, temperature, bucket, Test button and water are ruled out and the ice maker still will not make ice. At that point the problem is inside the machine — inlet valve, fill tube heater, ice maker module, auger motor, ice-room fan, or the seals in the ice room — and every one of those is tested with the power off and the machine open. A technician’s diagnosis follows the same order as this guide: temperature, then water, then the parts. The difference is that a technician tests each part rather than replacing parts by guesswork. Replacing an ice maker when the real problem is a seeping inlet valve means the new maker freezes over for exactly the same reason — which is why diagnosis comes before parts. For freezer and ice maker repair in Concord, NC, call (704) 755-6489. Before the visit, have ready: the model number from the inside label, which of the seven symptoms above matches yours, what the Test button did (chime, no chime, multiple chimes), and any error code on the display. That is the timeline a technician needs to diagnose it in one visit.

🛑 Stop Here — Call a Technician Instead

Call sooner — do not keep running the ice maker — if:

  • The ice maker is frozen over with a sheet of ice, or the bucket is stuck solid. Do not force it, and do not use a hair dryer or heat gun on it.
  • Water is pooling near an outlet, the power cord, or any electrical connection.
  • The same error code comes back after a reset.
  • The Test button does nothing at all, even after a 2-minute power cycle.
  • The freezer cannot reach 0°F — the problem is cooling, not the ice maker.
  • The ice maker freezes over again after a repair — the seal or the cooling loop behind it needs a technician’s diagnosis.

Repair or Replace?

As a rule of thumb: a repair that costs well under half the price of a comparable new refrigerator is usually worth doing, especially on a fridge that is otherwise cooling well. The repairs to evaluate carefully are the major ones — a sealed-system failure on top of an ice maker problem, or a fridge past year 10 with more than one thing wrong. Age alone is not the deciding factor. Before you pay for any repair, check your coverage first: look up your model and serial number on Samsung’s support site and at cpsc.gov to see whether your unit has warranty coverage or any extended coverage that applies. A diagnosis that names the failed part and the cause is what makes the decision possible — and it is also what tells you whether the same problem will come back.

Samsung Ice Makers We Service in Concord, NC

We diagnose and repair Samsung ice makers — French-door in-door models, side-by-side and top-freezer models, and Bespoke dual ice makers — along with the freezer and refrigerator systems behind them. The checks in this guide apply across the Samsung range; the parts and the test procedures differ by model, which is why the model number matters.

Serving Concord and the Surrounding Area

Concord Appliance Care serves Concord, NC and the surrounding Cabarrus County communities — including Harrisburg, Kannapolis, Mount Pleasant and Midland. Same-day service in most cases, and most repairs completed in a single visit.

Samsung Ice Maker Not Making Ice? Schedule a Diagnostic Today.

Samsung ice maker not making ice? Call (704) 755-6489. Hours: Monday–Friday 7:00 AM–7:00 PM, Saturday 8:00 AM–5:00 PM, Sunday emergency service only. Diagnosis first — you approve the cost before any repair.

Frequently Asked Questions

Why won’t my Samsung ice maker make ice? +
Check five things in order: the Ice Off icon, the freezer temperature (it must be 0°F or colder), the ice bucket (seated and clear), the Test button, and the water supply (6 ounces in under 10 seconds at the dispenser). Most no-ice cases end somewhere in that list. If the ice maker is frozen over with a sheet of ice, stop — Samsung says that needs service, not a hair dryer.
How do I reset my Samsung ice maker? +
Remove the ice bucket to find the Test button — on Bespoke dual makers, reach underneath the ice maker, above the bucket. Press and hold it until you hear a chime, which may take up to 10 seconds. The test takes about 6 minutes on an in-door ice maker or about 30 seconds on a freezer ice maker, and at the end the valve should hum and fill the tray. One chime means it passed. Do not press Test repeatedly, especially not with ice or water in the tray.
My water dispenser works but the ice maker doesn’t. Why? +
Working water confirms the home supply, the main inlet and the filter are not completely blocked — so the fault is in the ice-maker water path only. The usual suspects are the ice maker’s own Ice Off control, a frozen fill tube, the ice-side solenoid of the dual-port inlet valve, a failed ice-pipe heater, or the freezer being too warm for ice making while the dispenser still works.
Is cloudy ice from a Samsung fridge normal? +
Yes. Samsung says a normal cube from its ice makers is cloudy white, because rapid freezing traps small amounts of minerals, oxygen and nitrogen inside the ice. Small or shattered cubes are different — they mean low water flow. Dark flecks are not normal and usually mean an expired or damaged filter, or dirt in the water supply.
Why does my Samsung ice maker keep freezing over? +
Warm, humid kitchen air is leaking into the ice room past a seal that no longer seals — a bad ice bucket gasket, an ice route that does not close properly, or an air duct blocked with frost. Samsung has a technician service bulletin for this exact problem on French-door models. Do not defrost it yourself and do not use a hair dryer — Samsung says that can damage the ice maker. A freeze-over that keeps coming back is a service call.
How long should I wait for ice after fixing the problem? +
Samsung says you should begin to see normal ice production within 3 hours, and it may take a full 24 hours for production to return to normal amounts — about 2 trays every 3 hours. Dispense ice occasionally during that period so it does not pile up at one end of the bucket and make the maker think it is full.
What does error code 39E mean on a Samsung refrigerator? +
39E (or 39C) is an ice maker function error, according to Samsung’s own error-code list. It means the ice maker needs service. Photograph the display, do not unplug the fridge to clear the code, and do not keep resetting it — note the code and call for service. Codes vary by model, so if your code is not on Samsung’s list, do not guess at it.